Questions? Need Info? Phone: 800-475-4181

Replace Old Channels Perfectly with OEM or Aftermarket

Window Channels
Seal out the weather

Eliminate window rattles

Shown Left - CCOT's NEW!

Chrome beaded Channel

Fits FJ40 - '75 to '84

A CCOT Exclusive Product

Click Photo to Enlarge


FJ40 Channel for all years

Installation Instructions


Caution: Excessive force on window crank could damage window regulator. Be easy on crank (don't break crank / regulator when seating channel) and add WD40 or spread channel more to allow window to close.

FJ40 Soft Parts
Cross Section

Window Channel
Window Channel - No Flx  - 3 Pc - '58 - '74
Window Channel - No Flx - 3 Pc - '58 - '74


Click Photo to Enlarge

3 Piece Channel Set does 1 Door

Rigid - No Flex Channel Like OEM

Install Cross Channel first, then Side Channels.

Not "Handed" channel fits right or left front doors





Note: System will add $41.99 to base price for 2nd Window Channel.
$46.99
WINDCHANL-NoFlx-3Pce

Select: 
Cross Section

Window Channel
Black Flex Bead
'75-'84
Window Channel - Black Flx Bead - 75-84 - Aft Mrkt
Window Channel - Black Flx Bead - 75-84 - Aft Mrkt
  • Black beaded channels fits FJ40 - 1/'75 to '84
  • 2 channels does both front door
  • 70" Straight channel shapes to form corners
  • Not "Handed" channel fits right or left front doors
  • See Installation below



    Note: System will add $29.50 to base price for 2nd Window Channel.
  • $31.95
    WINDCHANL-BLK-Bead

    Select: 
    Window Channel, Chrome Flx Bead - 75 - 84 - Aft Mrkt
    Window Channel, Chrome Flx Bead - 75 - 84 - Aft Mrkt


    A CCOT Exclusive Part

    Flexible Chrome Beaded Window Channels

    Fits - FJ40 - 1/'75 to '84

    Channels are 70" straight lengths

    Channels are Custom Made to insert into window frame

    Channel flexes to form into corners of window frame

    These channels are offered nowhere else but at CCOT

    Installed chrome beaded channels look like OEM

    Not "Handed" channel fits right or left front doors

    See installation instructions below


    Click Image

    Note: System will add $36.00 to base price for 2nd Window Channel.
    $40.71
    WINDCHANL-CHRM-Bead

    Select: 
    Window Channel Chrome Bead - 1/75 - 8/80 - TOYOTA
    Window Channel Chrome Bead - 1/75 - 8/80 - TOYOTA
  • Toyota Part Updated Window Channel
  • OEM Channel for 1/'75 to 8/'80
  • Fits FJ40 FJ45
  • Not "Handed" fits right or left front doors
  • Black Felt liner with double chrome outer beads


    Note: System will add $101.94 to base price for 2nd Window Channel.
  • $106.94
    98105-60300

    Select: 
    Window Channel - Black Rubber - Updated - 8/'80-10/84 - TOYOTA
    Window Channel - Black Rubber - Updated - 8/'80-10/84 - TOYOTA
  • Toyota Part Updated Window Channel
  • OEM Channel for 8/'80 to 10/84
  • Not "Handed" fits right or left front doors
  • Black rubber window channel
  • Spring clips hold channel in window frame corners.


    Note: System will add $84.00 to base price for 2nd Window Channel.
  • $87.46
    98105-60302

    Select: 
    Installation Instructions -  Aft Mrkt - '75 to '84

    Click Photo to Enlarge

  • "A", Feed both ends of window channel (equal lengths ~ this will center channel) into door window grove while sliding and aligning window channel over window glass edges.




  • "B", Slightly pinch window channel to fit / insert into window grove. We use flat bill Vice-Grips to pinch channel.






  • "C", Once window channel is installed into window groove, then spread with wide / blunt screw driver to expand window channel to hold in place.



    Installation Details: First remove your old window channel. [Note: Do not remove smaller felt shaped "U" channel that is located just below the resting point (deep inside door) of the forward channel.] New window channel should be installed at room temperature (warm, not cold to be flexible). To install new channel into window frame grove, first slightly crimp / pinch width of channel so that it will insert into window frame grove. Window Channel is made slightly wider to hold in place once installed into window grove.] Once window channel is inserted into grove, then spread out (widen, with large blunt screw driver) channel so that it will hold in window frame grove. Finally, spray a light coat of WD40 into new channel to lubricate channel / glass when window is first rolled up to help seat channel.

    Caution: Excessive force on window crank could damage window regulator. Be easy on crank (don't break crank / regulator when seating channel) and add WD40 or spread channel more to allow window to close.
  • Door Wing Vent Glass Seal - '63-12/'74 - Passenger  Side - TOYOTA
    Door Wing Vent Glass Seal - '63-12/'74 - Passenger Side - TOYOTA


    This Toyota Seal Fits FJ40 Series '63 to 12/'74

    Seal Fits right side Door Wing Glass that's 16" Tall with push (button) and rotate lock located at base of Wing Glass.


    FYI - Wing Glass for 1958 to 1963 is 17" tall.

  • Both sides have been discontinued by Toyota
  • $37.91
    FJ40 Soft Parts
    Copyright © 1998 - 2013, CCOT, All rights reserved.
    Website Design by Solid Cactus
    We proudly accept American Express, Discover, Master Card, Visa, and PayPal This shopping cart employs the highest industry strength security: 256 bit SSL E-commerce by Yahoo!
    Cool Cruisers of Texas is not affiliated with Toyota Motor Corporation or Toyota Motor Sales.